| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on EX4k Series and QFX5k Series platforms allows an unauthenticated network-adjacent attacker flapping an interface to cause traffic between VXLAN Network Identifiers (VNIs) to drop, leading to a Denial of Service (DoS).
On all EX4k and QFX5k platforms, a link flap in an
EVPN-VXLAN configuration Link Aggregation Group (LAG)
results in Inter-VNI traffic dropping when there are multiple load-balanced next-hop routes for the same destination.
This issue is only applicable to systems that support EVPN-VXLAN Virtual Port-Link Aggregation Groups (VPLAG), such as the QFX5110, QFX5120, QFX5200, EX4100, EX4300, EX4400, and EX4650.
Service can only be restored by restarting the affected FPC via the 'request chassis fpc restart slot <slot-number>' command.
This issue affects Junos OS
on EX4k and QFX5k Series:
* all versions before 21.4R3-S12,
* all versions of 22.2
* from 22.4 before 22.4R3-S8,
* from 23.2 before 23.2R2-S5,
* from 23.4 before 23.4R2-S5,
* from 24.2 before 24.2R2-S3,
* from 24.4 before 24.4R2. |
| A Use After Free vulnerability in the chassis daemon (chassisd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based attacker authenticated with low privileges to cause a Denial-of-Service (DoS).
When telemetry collectors are frequently subscribing and unsubscribing to sensors continuously over a long period of time, telemetry-capable processes like chassisd, rpd or mib2d will crash and restart, which - depending on the process - can cause a complete outage until the system has recovered.
This issue affects:
Junos OS:
* all versions before 22.4R3-S8,
* 23.2 versions before 23.2R2-S5,
* 23.4 versions before 23.4R2;
Junos OS Evolved:
* all versions before 22.4R3-S8-EVO,
* 23.2 versions before 23.2R2-S5-EVO,
* 23.4 versions before 23.4R2-EVO. |
| An Unchecked Return Value vulnerability in the DNS module of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS).
If an SRX Series device configured for DNS processing, receives a specifically formatted DNS request flowd will crash and restart, which causes a service interruption until the process has recovered.
This issue affects Junos OS on SRX Series:
* 23.4 versions before 23.4R2-S5,
* 24.2 versions before 24.2R2-S1,
* 24.4 versions before 24.4R2.
This issue does not affect Junos OS versions before 23.4R1. |
| An Incorrect Initialization of Resource vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on specific EX Series and QFX Series device allows an unauthenticated, network-based attacker to cause an integrity impact to downstream networks.
When the same family inet or inet6 filter is applied on an IRB interface and on a physical interface as egress filter on EX4100, EX4400, EX4650 and QFX5120 devices, only one of the two filters will be applied, which can lead to traffic being sent out one of these interfaces which should have been blocked.
This issue affects Junos OS on EX Series and QFX Series:
* 23.4 version 23.4R2-S6,
* 24.2 version 24.2R2-S3.
No other Junos OS versions are affected. |
| A Stack-based Buffer Overflow vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS allows a network-based attacker, authenticated with low privileges to cause a Denial-of-Service (DoS).
Subscribing to telemetry sensors at scale causes all FPC connections to drop, resulting in an FPC crash and restart.
The issue was not seen when YANG packages for the specific sensors were installed.
This issue affects Junos OS:
* all versions before 22.4R3-S7,
* 23.2 version before 23.2R2-S4,
* 23.4 versions before 23.4R2. |
| A Use of a Broken or Risky Cryptographic Algorithm vulnerability in the TLS/SSL server of Juniper Networks Junos Space allows the use of static key ciphers (ssl-static-key-ciphers), reducing the confidentiality of on-path traffic communicated across the connection. These ciphers also do not support Perfect Forward Secrecy (PFS), affecting the long-term confidentiality of encrypted communications.This issue affects all versions of Junos Space before 24.1R5. |
| An Improper Locking vulnerability in the GTP plugin of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (Dos).
If an SRX Series device receives a specifically malformed GPRS Tunnelling Protocol (GTP) Modify Bearer Request message, a lock is acquired and never released. This results in other threads not being able to acquire a lock themselves, causing a watchdog timeout leading to FPC crash and restart. This issue leads to a complete traffic outage until the device has automatically recovered.
This issue affects Junos OS on SRX Series:
* all versions before 22.4R3-S8,
* 23.2 versions before 23.2R2-S5,
* 23.4 versions before 23.4R2-S6,
* 24.2 versions before 24.2R2-S3,
* 24.4 versions before 24.4R2-S2,
* 25.2 versions before 25.2R1-S1, 25.2R2. |
| A Loop with Unreachable Exit Condition ('Infinite Loop') vulnerability in the SIP application layer gateway (ALG) of Juniper Networks Junos OS on SRX Series and MX Series with MX-SPC3 or MS-MPC allows an unauthenticated network-based attacker sending specific SIP messages over TCP to crash the flow management process, leading to a Denial of Service (DoS).
On SRX Series, and MX Series with MX-SPC3 or MS-MPC service cards, receipt of multiple SIP messages causes the SIP headers to be parsed incorrectly, eventually causing a continuous loop and leading to a watchdog timer expiration, crashing the flowd process on SRX Series and MX Series with MX-SPC3, or mspmand process on MX Series with MS-MPC.
This issue only occurs over TCP. SIP messages sent over UDP cannot trigger this issue.
This issue affects Junos OS on SRX Series and MX Series with MX-SPC3 and MS-MPC:
* all versions before 21.2R3-S10,
* from 21.4 before 21.4R3-S12,
* from 22.4 before 22.4R3-S8,
* from 23.2 before 23.2R2-S5,
* from 23.4 before 23.4R2-S6,
* from 24.2 before 24.2R2-S3,
* from 24.4 before 24.4R2-S1,
* from 25.2 before 25.2R1-S1, 25.2R2. |
| An Improper Handling of Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated network-based attacker sending a specific ICMP packet through a GRE tunnel to cause the PFE to crash and restart.
When PowerMode IPsec (PMI) and GRE performance acceleration are enabled and the device receives a specific ICMP packet, a crash occurs in the SRX PFE, resulting in traffic loss. PMI is enabled by default, and GRE performance acceleration can be enabled by running the configuration command shown below. PMI is a mode of operation that provides IPsec performance improvements using Vector Packet Processing.
Note that PMI with GRE performance acceleration is only supported on specific SRX platforms.
This issue affects Junos OS on the SRX Series:
* all versions before 21.4R3-S12,
* from 22.4 before 22.4R3-S8,
* from 23.2 before 23.2R2-S5,
* from 23.4 before 23.4R2-S5,
* from 24.2 before 24.2R2-S3,
* from 24.4 before 24.4R2-S1,
* from 25.2 before 25.2R1-S1, 25.2R2. |
| A Use After Free vulnerability was identified in the 802.1X authentication daemon (dot1xd) of Juniper Networks Junos OS and Junos OS Evolved that could allow an authenticated, network-adjacent attacker flapping a port to crash the dot1xd process, leading to a Denial of Service (DoS), or potentially execute arbitrary code within the context of the process running as root.
The issue is specific to the processing of a change in authorization (CoA) when a port bounce occurs. A pointer is freed but was then referenced later in the same code path. Successful exploitation is outside the attacker's direct control due to the specific timing of the two events required to execute the vulnerable code path.
This issue affects systems with 802.1X authentication port-based network access control (PNAC) enabled.
This issue affects:
Junos OS:
* from 23.2R2-S1 before 23.2R2-S5,
* from 23.4R2 before 23.4R2-S6,
* from 24.2 before 24.2R2-S3,
* from 24.4 before 24.4R2-S1,
* from 25.2 before 25.2R1-S2, 25.2R2;
Junos OS Evolved:
* from 23.2R2-S1 before 23.2R2-S5-EVO,
* from 23.4R2 before 23.4R2-S6-EVO,
* from 24.2 before 24.2R2-S3-EVO,
* from 24.4 before 24.4R2-S1-EVO,
* from 25.2 before 25.2R1-S2-EVO, 25.2R2-EVO. |
| A Missing Release of Memory after Effective Lifetime vulnerability in the routing protocol daemon (rpd) Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated attacker controlling an adjacent IS-IS neighbor to send a specific update packet causing a memory leak. Continued receipt and processing of these packets will exhaust all available memory, crashing rpd and creating a Denial of Service (DoS) condition.
Memory usage can be monitored through the use of the 'show task memory detail' command. For example:
user@junos> show task memory detail | match ted-infra
TED-INFRA-COOKIE 25 1072 28 1184 229
user@junos>
show task memory detail | match ted-infra
TED-INFRA-COOKIE 31 1360 34 1472 307
This issue affects:
Junos OS:
* from 23.2 before 23.2R2,
* from 23.4 before 23.4R1-S2, 23.4R2,
* from 24.1 before 24.1R2;
Junos OS Evolved:
* from 23.2 before 23.2R2-EVO,
* from 23.4 before 23.4R1-S2-EVO, 23.4R2-EVO,
* from 24.1 before 24.1R2-EVO.
This issue does not affect Junos OS versions before 23.2R1 or Junos OS Evolved versions before 23.2R1-EVO. |
| An Incorrect Calculation vulnerability in the Layer 2 Control
Protocol
Daemon (l2cpd) of Juniper Networks Junos OS Evolved allows an unauthenticated network-adjacent attacker flapping the management interface to cause the learning of new MACs over label-switched interfaces (LSI) to stop while generating a flood of logs, resulting in high CPU usage.
When the issue is seen, the following log message will be generated:
op:1 flag:0x6 mac:xx:xx:xx:xx:xx:xx bd:2 ifl:13302 reason:0(REASON_NONE) i-op:6(INTRNL_OP_HW_FORCE_DELETE) status:10 lstatus:10 err:26(GETIFBD_VALIDATE_FAILED) err-reason 4(IFBD_VALIDATE_FAIL_EPOCH_MISMATCH) hw_wr:0x4 ctxsync:0 fwdsync:0 rtt-id:51 p_ifl:0 fwd_nh:0 svlbnh:0 event:- smask:0x100000000 dmask:0x0 mplsmask 0x1 act:0x5800 extf:0x0 pfe-id 0 hw-notif-ifl 13302 programmed-ifl 4294967295 pseudo-vtep underlay-ifl-idx 0 stack:GET_MAC, ALLOCATE_MAC, GET_IFL, GET_IFF, GET_IFBD, STOP,
This issue affects Junos OS Evolved:
* all versions before 21.4R3-S7-EVO,
* from 22.2 before 22.2R3-S4-EVO,
* from 22.3 before 22.3R3-S3-EVO,
* from 22.4 before 22.4R3-S2-EVO,
* from 23.2 before 23.2R2-S1-EVO,
* from 23.4 before 23.4R1-S2-EVO, 23.4R2-EVO. |
| A Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability in the method to collect FPC Ethernet firmware statistics of Juniper Networks Junos OS on MX10k Series allows a local, low-privileged attacker executing the 'show system firmware' CLI command to cause an LC480 or LC2101 line card to reset.
On MX10k Series systems with LC480 or LC2101 line cards, repeated execution of the 'show system firmware' CLI command can cause the line card to crash and restart. Additionally, some time after the line card crashes, chassisd may also crash and restart, generating a core dump.This issue affects Junos OS on MX10k Series:
* all versions before 21.2R3-S10,
* from 21.4 before 21.4R3-S9,
* from 22.2 before 22.2R3-S7,
* from 22.4 before 22.4R3-S6,
* from 23.2 before 23.2R2-S2,
* from 23.4 before 23.4R2-S3,
* from 24.2 before 24.2R2. |
| An Incorrect Initialization of Resource vulnerability in the Internal Device Manager (IDM) of Juniper Networks Junos OS on EX4000 models allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS).
On EX4000 models with 48 ports (EX4000-48T, EX4000-48P, EX4000-48MP) a high volume of traffic destined to the device will cause an FXPC crash and restart, which leads to a complete service outage until the device has automatically restarted.
The following reboot reason can be seen in the output of 'show chassis routing-engine' and as a log message:
reason=0x4000002 reason_string=0x4000002:watchdog + panic with core dump
This issue affects Junos OS on EX4000-48T, EX4000-48P and EX4000-48MP:
* 24.4 versions before 24.4R2,
* 25.2 versions before 25.2R1-S2, 25.2R2.
This issue does not affect versions before 24.4R1 as the first Junos OS version for the EX4000 models was 24.4R1. |
| An Improper Validation of Syntactic Correctness of Input vulnerability in the Web-Filtering module of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS).
If an SRX device configured for UTM Web-Filtering receives a specifically malformed SSL packet, this will cause an FPC crash and restart.
This issue affects Junos OS on SRX Series:
* 23.2 versions from 23.2R2-S2 before 23.2R2-S5,
* 23.4 versions from 23.4R2-S1 before 23.4R2-S5,
* 24.2 versions before 24.2R2-S2,
* 24.4 versions before 24.4R1-S3, 24.4R2.
Earlier versions of Junos are also affected, but no fix is available. |
| A Double Free vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX and MX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). On all SRX and MX Series platforms, when during TCP session establishment a specific sequence of packets is encountered a double free happens. This causes flowd to crash and the respective FPC to restart.
This issue affects Junos OS on SRX and MX Series:
* all versions before 22.4R3-S7,
* 23.2 versions before 23.2R2-S3,
* 23.4 versions before 23.4R2-S4,
* 24.2 versions before 24.2R2. |
| A Function Call With Incorrect Argument Type vulnerability in the sensor interface of Juniper Networks Junos OS Evolved on PTX Series allows a network-based, authenticated attacker with low privileges to cause a complete Denial of Service (DoS).
If colored SRTE policy tunnels are provisioned via PCEP, and gRPC is used to monitor traffic in these tunnels, evo-aftmand crashes and doesn't restart which leads to a complete and persistent service impact. The system has to be manually restarted to recover. The issue is seen only when the Originator ASN field in PCEP contains a value larger than 65,535 (32-bit ASN). The issue is not reproducible when SRTE policy tunnels are statically configured.
This issue affects Junos OS Evolved on PTX Series:
* all versions before 22.4R3-S9-EVO,
* 23.2 versions before 23.2R2-S6-EVO,
* 23.4 versions before 23.4R2-S7-EVO,
* 24.2 versions before 24.2R2-S4-EVO,
* 24.4 versions before 24.4R2-S2-EVO,
* 25.2 versions before 25.2R1-S2-EVO, 25.2R2-EVO. |
| A UNIX Symbolic Link (Symlink) Following vulnerability in the CLI of Juniper Networks Junos OS allows a local, authenticated attacker with low privileges to escalate their privileges to root which will lead to a complete compromise of the system.
When after a user has performed a specific 'file link ...' CLI operation, another user commits (unrelated configuration changes), the first user can login as root.
This issue affects Junos OS:
* all versions before 23.2R2-S7,
* 23.4 versions before 23.4R2-S6,
* 24.2 versions before 24.2R2-S3,
* 24.4 versions before 24.4R2-S2,
* 25.2 versions before 25.2R2.
This issue does not affect versions 25.4R1 or later. |
| An Incorrect Synchronization vulnerability in the management daemon (mgd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based attacker with low privileges to cause a complete Denial-of-Service (DoS) of the management plane.
When NETCONF sessions are quickly established and disconnected, a locking issue causes mgd processes to hang in an unusable state. When the maximum number of mgd processes has been reached, no new logins are possible. This leads to the inability to manage the device and requires a power-cycle to recover.
This issue can be monitored by checking for mgd processes in lockf state in the output of 'show system processes extensive':
user@host> show system processes extensive | match mgd
<pid> root 20 0 501M 4640K lockf 1 0:01 0.00% mgd
If the system still can be accessed (either via the CLI or as root, which might still be possible as last resort as this won't invoke mgd), mgd processes in this state can be killed with 'request system process terminate <PID>' from the CLI or with 'kill -9 <PID>' from the shell.
This issue affects:
Junos OS:
* 23.4 versions before 23.4R2-S4,
* 24.2 versions before 24.2R2-S1,
* 24.4 versions before 24.4R1-S3, 24.4R2;
This issue does not affect Junos OS versions before 23.4R1;
Junos OS Evolved:
* 23.4 versions before 23.4R2-S5-EVO,
* 24.2 versions before 24.2R2-S1-EVO,
* 24.4 versions before 24.4R1-S3-EVO, 24.4R2-EVO.
This issue does not affect Junos OS Evolved versions before 23.4R1-EVO; |
| A Missing Release of Memory after Effective Lifetime vulnerability in the Layer 2 Address Learning Daemon (l2ald) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause a memory leak ultimately leading to a Denial of Service (DoS).
In an EVPN-MPLS scenario, routes learned from remote multi-homed Provider Edge (PE) devices are programmed as ESI routes. Due to a logic issue in the l2ald memory management, memory allocated for these routes is not released when there is churn for these routes. As a result, memory leaks in the l2ald process which will ultimately lead to a crash and restart of l2ald.
Use the following command to monitor the memory consumption by l2ald:
user@device> show system process extensive | match "PID|l2ald"
This issue affects:
Junos OS:
* all versions before 22.4R3-S5,
* 23.2 versions before 23.2R2-S3,
* 23.4 versions before 23.4R2-S4,
* 24.2 versions before 24.2R2;
Junos OS Evolved:
* all versions before 22.4R3-S5-EVO,
* 23.2 versions before 23.2R2-S3-EVO,
* 23.4 versions before 23.4R2-S4-EVO,
* 24.2 versions before 24.2R2-EVO. |
